S60 on a vvti 3sge Toyota
-
- Posts: 82
- Joined: Fri May 30, 2014 7:36 am
- ECU Model: S60 Pro
- Distributor: mosley rolling road
- Firmware Version: 66
S60 on a vvti 3sge Toyota
As above using a s60 to run a 3sge rev4 Toyota. It's vvti on the inlet only. Just got the car started but cuts out after about a second. Check on the data logging and it shows the injectors are firing plug the coils are firing but cuts out. Anyone have an idea
-
- Posts: 1622
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: S60 on a vvti 3sge Toyota
Is sequential injection switched on? If so, turn it off.
Sounds like it's trying to run sequential injection, but the settings aren't correct.
Sounds like it's trying to run sequential injection, but the settings aren't correct.
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: S60 on a vvti 3sge Toyota
After working with a couple of Toyota triggers, I've worked out that the trigger angle and the cam angle will be different - no idea why (as there's no missing tooth) but that's how it works with them. I've run 1UZ and 4EFTE triggers. From memory I set the sequential switch point reasonably high and blipped the throttle to push rpm up and observed wher the timing shot off to. Once it got close I could adjust in a more normal manner. I used the Honda type trigger setting from memory.
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
-
- Posts: 82
- Joined: Fri May 30, 2014 7:36 am
- ECU Model: S60 Pro
- Distributor: mosley rolling road
- Firmware Version: 66
Re: S60 on a vvti 3sge Toyota
I've got it to run but need to set up the cam timing. Put the live chart up showing rpm tps and cam t and cam a and the cam t and a don't show in the 0 to 90 degree range. On the settings it's set at -313 will study the manual now but what's the best why to set the base cam settings.
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: S60 on a vvti 3sge Toyota
I haven't done a vvti one sorry.
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
-
- Posts: 82
- Joined: Fri May 30, 2014 7:36 am
- ECU Model: S60 Pro
- Distributor: mosley rolling road
- Firmware Version: 66
Re: S60 on a vvti 3sge Toyota
This is the same engine and it's now got me thinking of my coils
viewtopic.php?f=10&t=751&start=10
viewtopic.php?f=10&t=751&start=10
-
- Posts: 82
- Joined: Fri May 30, 2014 7:36 am
- ECU Model: S60 Pro
- Distributor: mosley rolling road
- Firmware Version: 66
-
- Posts: 82
- Joined: Fri May 30, 2014 7:36 am
- ECU Model: S60 Pro
- Distributor: mosley rolling road
- Firmware Version: 66