Hello,
My name is Stephen and i run a nissan micra rally car....
The engine is a 1348cc which has a skimmed and ported head, piper 773 cams and will be running on independent throttle bodies... I have an s80 ecu and would like some help with the start up map!
The car is running coil per plug as its the later model micra and i wish for it to stay that way! (non dizzy)
The TPS is off a gsxr 600
The Injectors are off a gsxr 600
Its running a 1 bar map sensor
Electric water pump and power steering
Any help would be greatly appreciated as im new to this!
Thanks for your time!
Ste
1400 Micra Throttlebodies Start Map
-
- Posts: 3
- Joined: Fri Mar 10, 2017 3:28 pm
- ECU Model: S80 Pro
-
- Posts: 1623
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: 1400 Micra Throttlebodies Start Map
If you can post a crankshaft oscilloscope, we'll get you up and running pretty quickly.
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: 1400 Micra Throttlebodies Start Map
The main thing to get running are the crank/cam triggers as Alex mentioned.
As for any sensors installed.
Read the manual and calibrate these yourself. It is the only way to ensure they will be correct for you.
As for any sensors installed.
Read the manual and calibrate these yourself. It is the only way to ensure they will be correct for you.
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: 1400 Micra Throttlebodies Start Map
As per what Stevie and Alex said.
If you don't have a knob box I'd set up an analogue input as a coarse fuel trim, that will let you get started even if your fuel map is miles off.
If you don't have a knob box I'd set up an analogue input as a coarse fuel trim, that will let you get started even if your fuel map is miles off.
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
-
- Posts: 3
- Joined: Fri Mar 10, 2017 3:28 pm
- ECU Model: S80 Pro
Re: 1400 Micra Throttlebodies Start Map
So here is an attachment of the crank sensor oscilloscope... ive not adjusted the crank sensor pickup angle yet as i am unsure of it but id like to know what the approx 6 or 186 degrees means...
And just while im here.. does this oscilloscope reading look ok?
Any help is appreciated thanks!
And just while im here.. does this oscilloscope reading look ok?
Any help is appreciated thanks!
-
- Posts: 1623
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: 1400 Micra Throttlebodies Start Map
You need to swap the two wires around on the crank sensor connector.
The 6 or 186 are an estimate of the crank sensor angle, but they're not correct because of the wiring issue.
That's a standard 60-2 pattern, so make sure that's in the general engine settings.
The 6 or 186 are an estimate of the crank sensor angle, but they're not correct because of the wiring issue.
That's a standard 60-2 pattern, so make sure that's in the general engine settings.
-
- Posts: 3
- Joined: Fri Mar 10, 2017 3:28 pm
- ECU Model: S80 Pro
Re: 1400 Micra Throttlebodies Start Map
Ahh thanks ! We did have mixed ideas about if we got them the right way around... and yeh I've set it to 60-2 thanks