1400 Micra Throttlebodies Start Map

Post maps up for others to get them going in the right direction. DISCLAIMER: USE AT YOUR OWN RISK. CONFIRM VALUES!
Post Reply
sterry9454
Posts: 3
Joined: Fri Mar 10, 2017 3:28 pm
ECU Model: S80 Pro

1400 Micra Throttlebodies Start Map

Post by sterry9454 »

Hello,
My name is Stephen and i run a nissan micra rally car....
The engine is a 1348cc which has a skimmed and ported head, piper 773 cams and will be running on independent throttle bodies... I have an s80 ecu and would like some help with the start up map!
The car is running coil per plug as its the later model micra and i wish for it to stay that way! (non dizzy)
The TPS is off a gsxr 600
The Injectors are off a gsxr 600
Its running a 1 bar map sensor
Electric water pump and power steering
Any help would be greatly appreciated as im new to this!
Thanks for your time!
Ste
Alex DTA
Posts: 1622
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: 1400 Micra Throttlebodies Start Map

Post by Alex DTA »

If you can post a crankshaft oscilloscope, we'll get you up and running pretty quickly.
stevieturbo
Posts: 3577
Joined: Tue Aug 02, 2011 12:08 pm
ECU Model: No ECU
Location: Norn Iron

Re: 1400 Micra Throttlebodies Start Map

Post by stevieturbo »

The main thing to get running are the crank/cam triggers as Alex mentioned.

As for any sensors installed.

Read the manual and calibrate these yourself. It is the only way to ensure they will be correct for you.
User avatar
ignitionautosport
Posts: 577
Joined: Wed Jul 27, 2011 5:30 am
ECU Model: S80 Pro
Location: New Zealand
Contact:

Re: 1400 Micra Throttlebodies Start Map

Post by ignitionautosport »

As per what Stevie and Alex said.

If you don't have a knob box I'd set up an analogue input as a coarse fuel trim, that will let you get started even if your fuel map is miles off.
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
sterry9454
Posts: 3
Joined: Fri Mar 10, 2017 3:28 pm
ECU Model: S80 Pro

Re: 1400 Micra Throttlebodies Start Map

Post by sterry9454 »

So here is an attachment of the crank sensor oscilloscope... ive not adjusted the crank sensor pickup angle yet as i am unsure of it but id like to know what the approx 6 or 186 degrees means...
And just while im here.. does this oscilloscope reading look ok?
Any help is appreciated :) thanks!
Attachments
Screenshot (20).png
Alex DTA
Posts: 1622
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: 1400 Micra Throttlebodies Start Map

Post by Alex DTA »

You need to swap the two wires around on the crank sensor connector.
The 6 or 186 are an estimate of the crank sensor angle, but they're not correct because of the wiring issue.

That's a standard 60-2 pattern, so make sure that's in the general engine settings.
sterry9454
Posts: 3
Joined: Fri Mar 10, 2017 3:28 pm
ECU Model: S80 Pro

Re: 1400 Micra Throttlebodies Start Map

Post by sterry9454 »

Ahh thanks ! We did have mixed ideas about if we got them the right way around... and yeh I've set it to 60-2 thanks :)
Post Reply