Hi all
Can anyone help, I need a start up map for my 4.8 twin turbo rv8, I'm using a p8 pro
Cheers
Disco
Start up map for 4.8 rover v8 on p8 pro
-
- Posts: 52
- Joined: Fri May 04, 2012 2:51 pm
- ECU Model: P8 Pro
-
- Posts: 3578
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Start up map for 4.8 rover v8 on p8 pro
Given you supply no information whatsoever, that will of course be impossible.
What trigger system are you using ? coils ? sensors ?
Working through the user manual, checking and calibrating all sensors in the software it should be very easy to build a basic map that will allow the engine to start.
What trigger system are you using ? coils ? sensors ?
Working through the user manual, checking and calibrating all sensors in the software it should be very easy to build a basic map that will allow the engine to start.
Re: Start up map for 4.8 rover v8 on p8 pro
Generally speaking, if user cannot build a basemap from scratch, it's better to tow car as it is to professional tuner or get a pro to do on-site job. This should be a sticky....
-
- Posts: 3578
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Start up map for 4.8 rover v8 on p8 pro
Well how else are they going to do it if they give no information whatsoever about their setup ?x30xe wrote:Generally speaking, if user cannot build a basemap from scratch, it's better to tow car as it is to professional tuner or get a pro to do on-site job. This should be a sticky....
If you follow a little common sense and the instructions. It's actually very easy to get a map that will at least start the engine.
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: Start up map for 4.8 rover v8 on p8 pro
unfortunately the usually best way is to work through the manual and get it started yourself. You will have far more understanding of how the trigger setup and ecu works. Trigger setup is one of the most painful things to do with any ecu.
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
-
- Posts: 52
- Joined: Fri May 04, 2012 2:51 pm
- ECU Model: P8 Pro
Re: Start up map for 4.8 rover v8 on p8 pro
I should have said that the guy that is putting my car together just asked if there was a base map floating around to save a bit of time, he is putting one together as I write this, then it's off to Steve Greenauld later this month
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: Start up map for 4.8 rover v8 on p8 pro
fair enough, always makes it easier.
Let us know how it goes
Let us know how it goes
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
-
- Posts: 3578
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Start up map for 4.8 rover v8 on p8 pro
There may be base maps. But until you specify what sensors and trigger setups you are using, nobody can ever know what you need.DiscoPotatoes wrote:I should have said that the guy that is putting my car together just asked if there was a base map floating around to save a bit of time, he is putting one together as I write this, then it's off to Steve Greenauld later this month
Any more details on the setup ? what vehicle etc ?
-
- Posts: 52
- Joined: Fri May 04, 2012 2:51 pm
- ECU Model: P8 Pro
Re: Start up map for 4.8 rover v8 on p8 pro
It's a tvr chimaera with twin gt 28rs turbos .86 A/R
3 bar map sensor and amal valve from DTA,Iat sensor, tps, stepper motor ,ford wasted spark coil packs gen 1, 36:1 tooth trigger wheel, innovate lc1 wideband, 60 lb rc racing saturated injectors,
Cross bolted block stage 3 heads and 45 mm trumpets port matched, 71 mm plenum,
7:1 comp Ross pistons,96mm bore top hat linered, carrillo rods, 4.6 crank, McLeod Rst clutch, t5 gearbox with up rated quiafe gear set from cts.
Have I missed anything?
3 bar map sensor and amal valve from DTA,Iat sensor, tps, stepper motor ,ford wasted spark coil packs gen 1, 36:1 tooth trigger wheel, innovate lc1 wideband, 60 lb rc racing saturated injectors,
Cross bolted block stage 3 heads and 45 mm trumpets port matched, 71 mm plenum,
7:1 comp Ross pistons,96mm bore top hat linered, carrillo rods, 4.6 crank, McLeod Rst clutch, t5 gearbox with up rated quiafe gear set from cts.
Have I missed anything?