It is currently Tue Oct 16, 2018 3:53 pm



Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: B16A2 map needed
PostPosted: Mon Oct 05, 2015 7:33 pm 
Offline

Joined: Fri May 30, 2014 12:42 am
Posts: 6
ECU Model: S40 Pro
Distributor: Watsons
Firmware Version: 62
Hi,

I am running an S40 that came with a Watsons kit to convert my Mini to Honda power, but the base map makes it hard to start and it runs fairly rough low down. Does anybody have a map that would help? I'm using a supplied Motorcraft powerpack instead of a dizzy but otherwise standard motor. And MAP not connected as yet, so only TPS, but I will connect same if a good supplied map uses it.
Failing which, does anybody know of a dyno in Perth, Western Australia, where the operator has ever worked with a DTA? I'm reluctant to spend a couple of grand waiting for the dyno man to come up to speed.

Thanks.


Top
 Profile  
 
 Post subject: Re: B16A2 map needed
PostPosted: Mon Oct 05, 2015 11:14 pm 
Offline
User avatar

Joined: Wed Jul 27, 2011 5:30 am
Posts: 571
Location: New Zealand
ECU Model: S80 Pro
I know of a guy in Aus though east side I think, I'll point him here though in case.

_________________
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz and also on Google+ |


Top
 Profile  
 
 Post subject: Re: B16A2 map needed
PostPosted: Sun Apr 03, 2016 1:00 pm 
Offline

Joined: Fri May 30, 2014 7:36 am
Posts: 73
ECU Model: S60 Pro
Distributor: mosley rolling road
Firmware Version: 66
I'm also looking for a map for this.


Top
 Profile  
 
 Post subject: Re: B16A2 map needed
PostPosted: Sun Apr 03, 2016 5:21 pm 
Offline

Joined: Tue Aug 02, 2011 12:08 pm
Posts: 2901
Location: Norn Iron
ECU Model: No ECU
As always, work through the manual and build your own calibration.

You need to check all settings anyway.

Largely the only slightly awkward bit might be crank trigger setup ( what are you using ? )

And ignition coil setup....again, what are you using ?

Some Honda's use an inverted coil charge not too unlike "external coil amps", but not sure if it's the same.
So OEM coil may not be compatible.


Top
 Profile  
 
 Post subject: Re: B16A2 map needed
PostPosted: Wed Nov 09, 2016 4:19 pm 
Offline

Joined: Wed Nov 09, 2016 8:25 am
Posts: 7
ECU Model: S40 Pro
Firmware Version: 79,02
i have different maps for the honda b16a2 engine. NA or turbo

send me an email
turbo6@hotmail.com

if you have a good turbo map, please send it to me !
same email adress


Top
 Profile  
 
 Post subject: Re: B16A2 map needed
PostPosted: Fri Jul 28, 2017 4:01 pm 
Offline

Joined: Sun Jul 23, 2017 2:30 pm
Posts: 17
ECU Model: S60 Pro
Hello everybody

I'm searching for a Honda b16a2 OEM N/A map for my s60.
I will use some custom sensors to manage the rpm and cam and a custom ignition coil from motorbike.

I only need a map to have fuel and ignition table and make a quick start to control the loom, gearbox ...etc

After that I will bring my car to a professional tunner
So I only need a base map very close to an OEM B16a2 engine

Thanks


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Theme designed by stylerbb.net © 2008
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
All times are UTC - 5 hours