Generic map/running in

This section is dedicated to discussion of DTA engine control units such as the DTA E48 EXP, P8 Pro, DTA S40, S60, S80, and S100, as well as all things ECU related.
Alex DTA
Posts: 1622
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: Generic map/running in

Post by Alex DTA »

OK, there's no preset value for that one, so you'll just need to scale it.

Email me for a map when you're ready.
Daniboy123
Posts: 16
Joined: Sat Nov 05, 2016 9:13 pm
ECU Model: S80 Pro

Re: Generic map/running in

Post by Daniboy123 »

Is the scaling a case of inputting 20 voltage/lambda values or have I misread that from the manual?
Daniboy123
Posts: 16
Joined: Sat Nov 05, 2016 9:13 pm
ECU Model: S80 Pro

Re: Generic map/running in

Post by Daniboy123 »

Is the scaling a case of inputting 20 voltage/lambda values or have I misread that from the manual?
Alex DTA
Posts: 1622
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: Generic map/running in

Post by Alex DTA »

That's it. Should be in the manual for your controller.
Daniboy123
Posts: 16
Joined: Sat Nov 05, 2016 9:13 pm
ECU Model: S80 Pro

Re: Generic map/running in

Post by Daniboy123 »

I've had a look through the online manual and I've found that there are two analogue outputs, one is 0V = 7.35 AFR and 5V = 22AFR. The other is for a narrow band sensor so no use to me.
katana
Posts: 455
Joined: Sun Jan 27, 2013 6:08 pm
ECU Model: S60 Pro
Firmware Version: 29

Re: Generic map/running in

Post by katana »

So 22.00 - 7.35 = 14.65 / 20 = 0.73 added to previous cell from 7.35 will give linear scaling .....1st cell 7.35, 2nd cell 8.08, 3rd cell 8.81 etc etc. Or I think you can put in 1st and last numbers in and ask DTA to extrapolate the numbers between with same result. But if you are using an Innovate Controller why not just select that from the list and it'll auto set it for you?
Daniboy123
Posts: 16
Joined: Sat Nov 05, 2016 9:13 pm
ECU Model: S80 Pro

Re: Generic map/running in

Post by Daniboy123 »

I don't think the Mtx-l sensor has been added to the list? I've seen the lm-1 and lm-2 sensors on there.
katana
Posts: 455
Joined: Sun Jan 27, 2013 6:08 pm
ECU Model: S60 Pro
Firmware Version: 29

Re: Generic map/running in

Post by katana »

Ok whilst not listed I can't imagine Innovate would change their outputs between products - I'd be tempted to try the IM-1 or 2 listing?
Alex DTA
Posts: 1622
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: Generic map/running in

Post by Alex DTA »

LC1/LC2/LM1/LM2/MTX-L all use the same output, so just select that one.
Daniboy123
Posts: 16
Joined: Sat Nov 05, 2016 9:13 pm
ECU Model: S80 Pro

Re: Generic map/running in

Post by Daniboy123 »

Yea just checked the lm-2 online manual before seeing the replies to see its exactly the same output. Now I just need to set up my crank shafts sensor and take a picture, send it over to sparrow off club gti not sure who that is on here and get the generic map.
Post Reply