first start 1.8T AGU

This section is dedicated to discussion of DTA engine control units such as the DTA E48 EXP, P8 Pro, DTA S40, S60, S80, and S100, as well as all things ECU related.
f.slabsi
Posts: 16
Joined: Thu Mar 16, 2017 5:37 am
ECU Model: S60 Pro
Distributor: DTAfast
Firmware Version: 68.00

first start 1.8T AGU

Post by f.slabsi »

Please, I need to consult the basic settings for DTA S60 series engine 1.8T AGU. see photo
Attachments
Osciloskop.JPG
General settings.JPG
osci fabia1.JPG
f.slabsi
Posts: 16
Joined: Thu Mar 16, 2017 5:37 am
ECU Model: S60 Pro
Distributor: DTAfast
Firmware Version: 68.00

Re: first start 1.8T AGU

Post by f.slabsi »

I entered in the General settings: position sensor value 74 or 254, but still nothing.
iceman_n
Posts: 141
Joined: Mon Jan 16, 2012 1:39 pm
ECU Model: S40 Pro
Firmware Version: 58

Re: first start 1.8T AGU

Post by iceman_n »

firing tooth on start up 1 or 2, try the 1 first...

also enter injectors cc and i think injector dead time is high...

also injector start pulse try with 7-10

then when you finish with this setup open diagnostic display and crank the engine without injectors and coils and see if it sychronise and become green

if it stays green then plug the injectors and coil and try again if it stays green again means it sychronise...then try to fire up the engine

also you need fuel on engine start fuelling field and corrent advance and fuel on main map

ask Alex a map fron vw 1.8 engine so you can have a good starting point
f.slabsi
Posts: 16
Joined: Thu Mar 16, 2017 5:37 am
ECU Model: S60 Pro
Distributor: DTAfast
Firmware Version: 68.00

Re: first start 1.8T AGU

Post by f.slabsi »

When I have plugged oil pressure sensor, it is possible that the unit can not be impulse to start the engine?
f.slabsi
Posts: 16
Joined: Thu Mar 16, 2017 5:37 am
ECU Model: S60 Pro
Distributor: DTAfast
Firmware Version: 68.00

Re: first start 1.8T AGU

Post by f.slabsi »

I am well-connected coils and spray? by engagement, I'm sure someone will show me how to properly engage on cylider?
Alex DTA
Posts: 1622
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: first start 1.8T AGU

Post by Alex DTA »

Do you have the original amplifier for the coils?

I'll post a map tomorrow for an AGU, but I need to know if you have the coil amplifiers or not.
f.slabsi
Posts: 16
Joined: Thu Mar 16, 2017 5:37 am
ECU Model: S60 Pro
Distributor: DTAfast
Firmware Version: 68.00

Re: first start 1.8T AGU

Post by f.slabsi »

Yes, I have the original amplifier coils
Alex DTA
Posts: 1622
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: first start 1.8T AGU

Post by Alex DTA »

Here's a start up map
Attachments
VW Golf AGU.map
(45.31 KiB) Downloaded 265 times
f.slabsi
Posts: 16
Joined: Thu Mar 16, 2017 5:37 am
ECU Model: S60 Pro
Distributor: DTAfast
Firmware Version: 68.00

Re: first start 1.8T AGU

Post by f.slabsi »

Thank you for the quick response, tomorrow I'll try and let you know
f.slabsi
Posts: 16
Joined: Thu Mar 16, 2017 5:37 am
ECU Model: S60 Pro
Distributor: DTAfast
Firmware Version: 68.00

Re: first start 1.8T AGU

Post by f.slabsi »

I progressed, synchronization ok - was faulty speed sensor cam. I can tweak the timing when the engine has started running on two cylinders (2 and 4). where I have a problem? When the engine is running on two cylinders I had a position sensor 78. When starting the engine burn before TDC. motor kicking
Post Reply