S100 coil driver

Discuss which Sensors work best with these ECUs and share how you are using inputs and outputs
Keithd2959
Posts: 13
Joined: Thu Sep 01, 2016 12:41 am
ECU Model: S100 Pro

S100 coil driver

Post by Keithd2959 »

Hi all, just bought an s100 for my s2000 ap engine and was trying to figure out if the dta s100 can drive the oem coils directly of the s2000. The coil are of the 3wire type, power, ground and signal. Any help please? Thanks
iceman_n
Posts: 141
Joined: Mon Jan 16, 2012 1:39 pm
ECU Model: S40 Pro
Firmware Version: 58

Re: S100 coil driver

Post by iceman_n »

yes s100 can drive them directly...probably the s2000 coils are amplified coils so you need to enable the "external coil amps" on general engine settings

if your coils are not amplified you dont need to enable this feature...so be sure if your coils are amplified or not first....
Keithd2959
Posts: 13
Joined: Thu Sep 01, 2016 12:41 am
ECU Model: S100 Pro

Re: S100 coil driver

Post by Keithd2959 »

Thanks for your prompt reply. Is there a way to physically check if they are amplified or not?
Keithd2959
Posts: 13
Joined: Thu Sep 01, 2016 12:41 am
ECU Model: S100 Pro

Re: S100 coil driver

Post by Keithd2959 »

Anyone using the honda coils p/n: 30520-rra-007 with the dts s100?
PhillipM
Posts: 177
Joined: Tue May 13, 2014 5:30 am
ECU Model: S80 Pro
Distributor: DTA UK
Firmware Version: 73

Re: S100 coil driver

Post by PhillipM »

They're amplified, I'm using the later 09+ coils but I think wiring/driving wise they're exactly the same anyway.

Beware if you're wiring it in using the manual, because the instructions for the S2000 both wiring and trigger settings are wrong for the later cars
Keithd2959
Posts: 13
Joined: Thu Sep 01, 2016 12:41 am
ECU Model: S100 Pro

Re: S100 coil driver

Post by Keithd2959 »

Perfect thanks.
Keithd2959
Posts: 13
Joined: Thu Sep 01, 2016 12:41 am
ECU Model: S100 Pro

Re: S100 coil driver

Post by Keithd2959 »

Thanks for the info. Infact I think the base map from dta is for an earlier model, mine is an 06 ap2.
PhillipM
Posts: 177
Joined: Tue May 13, 2014 5:30 am
ECU Model: S80 Pro
Distributor: DTA UK
Firmware Version: 73

Re: S100 coil driver

Post by PhillipM »

Yes, the base map must be one of the 05 or earlier I think. My engine has the K20 timing wheel/sensor setup although the crank sensor is wired slightly differently numbers wise on the pins IIRC.
Keithd2959
Posts: 13
Joined: Thu Sep 01, 2016 12:41 am
ECU Model: S100 Pro

Re: S100 coil driver

Post by Keithd2959 »

Hi again, just to make sure I'm correct. The s100 can't drive a wideband lambda sensor directly, an external controller has to be used correct? Thanks
Rob Stevens
Posts: 1247
Joined: Thu Jul 28, 2011 4:10 am
ECU Model: S100 Pro
Distributor: None-Coil On Plug :)

Re: S100 coil driver

Post by Rob Stevens »

correct, external controller required. Just follow the drawing. I use the fuel pump circuit to turn the controller on and off.
Post Reply