Flex fuel sensor
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Flex fuel sensor
Given the Continetnal sensor seems to be the most widely used, would it make sense to test it and give it as an option ? Especially as it's a fraction of the price of the GM sensor.
Re: Flex fuel sensor
The output signals are identical between the two common Siemens & Continental FCS. The only difference that I know of that may effect the compatibility with DTA is the Siemens (GM) needs a stronger pull-up to 5V, typically 2.2K, whereas the Continental wont drive a load of any more than about 3K.
I don't know what value pull-up DTA use on its DI or if it can be turned off by software or perhaps a PCB jumper but if the pull-up is lower than about 3K the Continental sensor wont work (at least reliably).
I don't know what value pull-up DTA use on its DI or if it can be turned off by software or perhaps a PCB jumper but if the pull-up is lower than about 3K the Continental sensor wont work (at least reliably).
Re: Flex fuel sensor
On a side note, does anyone know if these ethanol sensors will work with methanol.
I run 20% meth and this would make the car a lot more practical.
I run 20% meth and this would make the car a lot more practical.
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Flex fuel sensor
I havent tried it myself, but I know some of the Subaru guys using the Continental sensor have reported it does recognise a difference when methanol is added.gnutz2 wrote:On a side note, does anyone know if these ethanol sensors will work with methanol.
I run 20% meth and this would make the car a lot more practical.
Re: Flex fuel sensor
Thanks, nice to know, although its a shame they're so expensive.
Just to clarify, the GM sensor (that dta supports) outputs a duty cycle and frequency based on ethanol and temperature and the cheap continental sensors put out 0-5v based on ethanol content.
So quite simply we could use the continental sensor wired to a spare auxiliary input and adjust the fuel and timing from there.
Just to clarify, the GM sensor (that dta supports) outputs a duty cycle and frequency based on ethanol and temperature and the cheap continental sensors put out 0-5v based on ethanol content.
So quite simply we could use the continental sensor wired to a spare auxiliary input and adjust the fuel and timing from there.
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: Flex fuel sensor
No - methanol will give an incorrect/odd reading, as will water absorbed in ethanol.stevieturbo wrote:I havent tried it myself, but I know some of the Subaru guys using the Continental sensor have reported it does recognise a difference when methanol is added.gnutz2 wrote:On a side note, does anyone know if these ethanol sensors will work with methanol.
I run 20% meth and this would make the car a lot more practical.
Had a race team using E85 tell us the ethanol content readout we made using one of these sensors was wrong - turns out they were using old fuel.
I'm curious how this would work with what we have available in NZ, E100 readily available here is denatured with 1.5% methanol. E85 has 0.5 to 1% methanol from memory (the race stuff at least).
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Flex fuel sensor
methanol will give a reading, how you calibrate the reading is up to you, but based on Tim's testing, whether ethanol or methanol the sensor doesnt differentiate.
Obviously this would then get awkward if wanting to mix petrol, methanol and ethanol. I'd doubt many would do that though
http://bbs.22b.com/forums/showthread.ph ... ensors-EOI
And I thought most flex fuel sensors are frequency based ? Although technically the output is still in the 0-5v range
Obviously this would then get awkward if wanting to mix petrol, methanol and ethanol. I'd doubt many would do that though
http://bbs.22b.com/forums/showthread.ph ... ensors-EOI
And I thought most flex fuel sensors are frequency based ? Although technically the output is still in the 0-5v range
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Flex fuel sensor
other interesting info
http://www.gtrheritage.com/topic/2770-b ... ely-blown/
Interesting these guys mention a Ford sensor, that looks very like the GM sensor
http://www.supraforums.com/forum/showth ... uel-sensor
But both threads seem to suggest they all operate within quite similar ranges and ways
http://www.gtrheritage.com/topic/2770-b ... ely-blown/
Interesting these guys mention a Ford sensor, that looks very like the GM sensor
http://www.supraforums.com/forum/showth ... uel-sensor
But both threads seem to suggest they all operate within quite similar ranges and ways
Re: Flex fuel sensor
Well we cant find out until someone tries i guess.
Also my car it tuned on E85, so only need this for a few hours of winter driving, not that E85 cant be runnd in freezing cold weather, but i don't need the extra HP in the winter, and pump gas is easier to find, and better for the injectors for storing all winter
Also my car it tuned on E85, so only need this for a few hours of winter driving, not that E85 cant be runnd in freezing cold weather, but i don't need the extra HP in the winter, and pump gas is easier to find, and better for the injectors for storing all winter
Re: Flex fuel sensor
Fond new GM sensor for 150$ on ebay,
I have only seen usen ones in this pricerange, so i got that one