pro8 datalog
-
- Posts: 4
- Joined: Fri May 31, 2013 12:14 am
- ECU Model: P8 Pro
pro8 datalog
is there any decent way to view pro8 data logs? besides just scrolling through pages of data? erace, just gives me blank graphs
-
- Posts: 3577
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: pro8 datalog
E-race should work fine. Just import it first.
Or Megalog viewer should work too.
Or Megalog viewer should work too.
-
- Posts: 4
- Joined: Fri May 31, 2013 12:14 am
- ECU Model: P8 Pro
Re: pro8 datalog
i have tried both but will attempt a few more times
-
- Posts: 3577
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: pro8 datalog
Post a log file up
-
- Posts: 4
- Joined: Fri May 31, 2013 12:14 am
- ECU Model: P8 Pro
-
- Posts: 1247
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: pro8 datalog
Looks fine to me, perhaps you are having trouble using e-race? I note that you are not logging the TPS. I see a peak of 7000 rpm and 1.6 bar, is this some tractor engine?
Open erace
Data - Import
Browse to your data
Make and slecet a track
Make and select a sesion
Import
Then
Data - Data Manager
Select the file you just imported
then the graphs should come up
you can change what you look at with 'show channels'
Make sure that you select what you want to log in the DTA software
Open erace
Data - Import
Browse to your data
Make and slecet a track
Make and select a sesion
Import
Then
Data - Data Manager
Select the file you just imported
then the graphs should come up
you can change what you look at with 'show channels'
Make sure that you select what you want to log in the DTA software
-
- Posts: 3577
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: pro8 datalog
Just added a bit to the above. It works fine in E-race for me, but wont open with MLV. Phil maybe hasnt configured MLV for the older logs of the P8 etcRob Stevens wrote:Looks fine to me, perhaps you are having trouble using e-race? I note that you are not logging the TPS. I see a peak of 7000 rpm and 1.6 bar, is this some tractor engine?
Open erace
Data - Import
Browse to your data
Make and select a track
Make and select a session
Select "reverse data" on
Import
Then
Data - Data Manager
Select the file you just imported
then the graphs should come up
you can change what you look at with 'show channels'
Make sure that you select what you want to log in the DTA software
The 250kpa boost reading is just an erroneous spike for some reason. Mostly seems a peak of around 0.5 bar boost, ie 150kpa. No TPS or lambda logged.
-
- Posts: 52
- Joined: Fri May 04, 2012 2:51 pm
- ECU Model: P8 Pro
Re: pro8 datalog
I just thought I'd have a look at erace, followed your instruction but I'm having the same problem as the op and I'm getting a blank graph no data shown!
-
- Posts: 3577
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: pro8 datalog
you need to drag the data from the right onto the blank graphs to view what you want
-
- Posts: 52
- Joined: Fri May 04, 2012 2:51 pm
- ECU Model: P8 Pro
Re: pro8 datalog
Ah ha! Brilliant that worked a treat?stevieturbo wrote:you need to drag the data from the right onto the blank graphs to view what you want
Cheers