Flashing DTA S-Series

Discuss issues and tuning software like DTASWin, E-Race, MegaLogViewer(DTA), etc. Also post archive versions of firmware.
Bigboss
Posts: 5
Joined: Tue May 30, 2017 2:01 pm
ECU Model: S80 Pro
Firmware Version: 89.00

Re: Flashing DTA S-Series

Post by Bigboss »

"It just seems to explain how to use DTA SWin to view the current firmware, and to verify you have comms ok with the laptop

And likewise after any flashing to confirm that it has all worked ok."


Now I see! The part that describes what softwares needed are in wrong order.
Below you see the dot-headers and the following "blue download-button text":

• ST10 Flasher Software
DTASWin For S Series ECUs
DTASWin v80.07

• DTA Swin Software
S Series ECU Flash Program
S Series ECU Firmware Upgrade Software


It should be like this:

• DTA Swin Software
DTASWin For S Series ECUs
DTASWin v80.07

• ST10 Flasher Software
S Series ECU Flash Program
S Series ECU Firmware Upgrade Software


"You're very lucky to have managed to do it since the ST10 Flasher software is very "flakey" and sometimes takes 100's of attempts to work! The problem seems to be getting the monitor to load, it usually says "monitor failed to load"."

I did this operation seven yers ago as well and got lucky that time also. And still I was confused after reading the instruction yesterday. The brain is not perfect, so to say.
stevieturbo
Posts: 3577
Joined: Tue Aug 02, 2011 12:08 pm
ECU Model: No ECU
Location: Norn Iron

Re: Flashing DTA S-Series

Post by stevieturbo »

I agree, it isnt totally clear.

But I think the success is largely down to a direct serial port.
firemanjim
Posts: 14
Joined: Tue Jan 28, 2020 5:09 pm
ECU Model: S80 Pro

Re: Flashing DTA S-Series

Post by firemanjim »

Downloaded to flash software and latest firmware, have the cable with the button. having no success . First had to set proper com port, now it says load monitor error, fail to acknowledge??
Rob Stevens
Posts: 1247
Joined: Thu Jul 28, 2011 4:10 am
ECU Model: S100 Pro
Distributor: None-Coil On Plug :)

Re: Flashing DTA S-Series

Post by Rob Stevens »

I've found it a bit flaky. try at least 15 times!
firemanjim
Posts: 14
Joined: Tue Jan 28, 2020 5:09 pm
ECU Model: S80 Pro

Re: Flashing DTA S-Series

Post by firemanjim »

Way over that, two different cables, 2 different laptops, at least 50 tries. WTF uses a damn serial port any more-- seriously! Try to find a computer with one nowadays! Going to see if I can resurrect and old Dell. And when I have the flasher open and ask it to search for the hex file I can see on my desktop, it cannot seem to find it. Again WTF!!!!
stevieturbo
Posts: 3577
Joined: Tue Aug 02, 2011 12:08 pm
ECU Model: No ECU
Location: Norn Iron

Re: Flashing DTA S-Series

Post by stevieturbo »

firemanjim wrote:Way over that, two different cables, 2 different laptops, at least 50 tries. WTF uses a damn serial port any more-- seriously! Try to find a computer with one nowadays! Going to see if I can resurrect and old Dell. And when I have the flasher open and ask it to search for the hex file I can see on my desktop, it cannot seem to find it. Again WTF!!!!
Home PC does.

If DTASwin connects via the USB...then you should be ok.

So verify that first. Shut it down, then run the flasher.

And are you sure you're following instructions ? Is the ecu even in flash mode ?
firemanjim
Posts: 14
Joined: Tue Jan 28, 2020 5:09 pm
ECU Model: S80 Pro

Re: Flashing DTA S-Series

Post by firemanjim »

Cables both connect. I am trying to follow instructions, guess I missed putting ecu in flash mode, elaborate please----
firemanjim
Posts: 14
Joined: Tue Jan 28, 2020 5:09 pm
ECU Model: S80 Pro

Re: Flashing DTA S-Series

Post by firemanjim »

Do you do the press flash button, then open the flasher?
firemanjim
Posts: 14
Joined: Tue Jan 28, 2020 5:09 pm
ECU Model: S80 Pro

Re: Flashing DTA S-Series

Post by firemanjim »

My cable has the button and verified it works with ohm meter, verified fuel pump wired to ecu as diagram says, no matter what I do holding button fuel pump always comes on. Is there a pin out for that cable so I can be sure it is wired to correct pins?
firemanjim
Posts: 14
Joined: Tue Jan 28, 2020 5:09 pm
ECU Model: S80 Pro

Re: Flashing DTA S-Series

Post by firemanjim »

At this point I am unsure what the correct order to do all of this in.
Post Reply