Cam and cranck sensor????

Discuss which Sensors work best with these ECUs and share how you are using inputs and outputs

Cam and cranck sensor????

Postby Andreas Norway » Sat Nov 11, 2017 3:18 pm

Hi im looking att the wiring chart for cam and cranck sensors on the S60 but getting confused wen i read the textbox on the bottom left corner.
Can i use both cam and crank magnetic and can i shield them together to sensor GND??
It says i can ony use one at any time so thats whats get me stuck.
Living life sideways
Andreas Norway
 
Posts: 43
Joined: Mon May 16, 2016 8:01 am
Location: Norway
ECU Model: S60 Pro
Distributor: Kl racing

Re: Cam and cranck sensor????

Postby Alex DTA » Sat Nov 11, 2017 3:49 pm

You can use two magnetic sensors, that's fine.

The wiring diagram is making sure you don't connect a magnetic crank sensor AND a Hall effect crank sensor.
Alex DTA
 
Posts: 1275
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: Cam and cranck sensor????

Postby Andreas Norway » Sat Nov 11, 2017 4:17 pm

Alex DTA wrote:You can use two magnetic sensors, that's fine.

The wiring diagram is making sure you don't connect a magnetic crank sensor AND a Hall effect crank sensor.



Aha as i expected :D just wanna be sure..
Tnx for answer Alex
Living life sideways
Andreas Norway
 
Posts: 43
Joined: Mon May 16, 2016 8:01 am
Location: Norway
ECU Model: S60 Pro
Distributor: Kl racing

Re: Cam and cranck sensor????

Postby SMR » Fri Feb 16, 2018 3:20 am

Hi Alex,
On a similar subject - I plan to use a magnetic crank sensor (Pins 12 & 21) and Hall effects cam sensor (Pins 23, 21SG and 5v from 9);
Is this combination ok?

Cheers
Steve
SMR
 
Posts: 64
Joined: Tue Jan 16, 2018 9:38 am
Location: Aberdeen
ECU Model: S100 Pro
Distributor: DTA

Re: Cam and cranck sensor????

Postby Alex DTA » Fri Feb 16, 2018 3:52 am

Hi Steve
Yes, that's fine.

The text is meant to warn against fitting a hall and magnetic crank (or cam) sensor to the same ECU.
Alex DTA
 
Posts: 1275
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Re: Cam and cranck sensor????

Postby SMR » Fri Feb 16, 2018 1:56 pm

Cheers Alex, I did search the forum and found some useful info, but good to get confirmation!
SMR
 
Posts: 64
Joined: Tue Jan 16, 2018 9:38 am
Location: Aberdeen
ECU Model: S100 Pro
Distributor: DTA

Re: Cam and cranck sensor????

Postby mike31 » Mon Aug 20, 2018 2:48 am

Hi,
Just to be sure too, when i read the crank sensor connections on diagrams pages, it talking about Sensor ground and Sensor ground at ECU.
So Sensor Ground is on pin 33 and sensor ground at ECU is the wiring shield on the ECU casing ?

Cheers
mike31
 
Posts: 6
Joined: Thu Mar 01, 2018 1:07 pm
ECU Model: S60 Pro

Re: Cam and cranck sensor????

Postby Antral » Mon Aug 20, 2018 4:52 am

No.

You need to splice the S/Gnd wire to the shield at the ECU end then put the pin in 33 or 21

Tony.
Antral
 
Posts: 185
Joined: Mon Aug 01, 2011 8:20 am

Re: Cam and cranck sensor????

Postby mike31 » Mon Aug 20, 2018 8:44 am

Ok
So 1 signal crank or cam to ecu and both ground, sensor and shield to pin 33 or 21 right ?
Thx
mike31
 
Posts: 6
Joined: Thu Mar 01, 2018 1:07 pm
ECU Model: S60 Pro

Re: Cam and cranck sensor????

Postby Alex DTA » Mon Aug 20, 2018 2:20 pm

Just to be clear.

You must have a crank sensor. This goes to pin 12 if VR.
Sensor ground goes to pin 21. If there's a shield, that also goes to pin 21.

If you have a cam sensor, it goes to the the correct signal.
Ground goes to pin 21.
If there's a shield, it also goes to pin 21.
Alex DTA
 
Posts: 1275
Joined: Fri Feb 28, 2014 1:03 pm
ECU Model: S40 Pro
Distributor: DTA
Firmware Version: 79

Next

Return to Sensors, Inputs, and Outputs

Who is online

Users browsing this forum: No registered users and 3 guests