How do you setup/wire S60 to switch fuel and ign' map from a switch on the dash. Which pin, of which connector, is it pulled down to earth, etc, etc.
Thanks
BP
Wiring to switch Map from Dash
-
- Posts: 1250
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: Wiring to switch Map from Dash
read the drawing, I think pin 15 to ground on the sensor connector.
-
- Posts: 3
- Joined: Sat Aug 31, 2013 2:31 pm
- ECU Model: S60 Pro
- Location: Northern Ireland
- Contact:
Re: Wiring to switch Map from Dash
Thanks was not very clear from drawing. Description on Pin 15 reads ALS/Map 2 and Lambda Switch. Now that I know this is the pin this makes sense, not having a turbo charged car I had dismissed this as an anti-lag setting.
Must read the whole user manual again.
Must read the whole user manual again.
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Wiring to switch Map from Dash
To be fair, the grouping of functions for a single pin can be annoying and the ALS/MAP2 should be a thing of the past and have ALS completely divorced from any maps.
-
- Posts: 1250
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: Wiring to switch Map from Dash
Yeh, you can't use the Lambda on map 2
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Wiring to switch Map from Dash
Closed loop can still be active on MAP2 ( S-series anyway and pretty sure older ecu's )Rob Stevens wrote:Yeh, you can't use the Lambda on map 2
But, you must have CL active all the time, ie the box checked.
The switch only does the MAP1/MAP2 function.
The fuel correction map will still be generated, however if you try and apply these corrections, they will be made to MAP1
Likewise with lambda logging on the PC....it will record the info, but only let you apply any changes to MAP1
Another issue that really needs changed
-
- Posts: 1250
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: Wiring to switch Map from Dash
Ok Steve, I meant to say that you can't use the Lambda switch on Map 2. Sorry.
-
- Posts: 12
- Joined: Tue Oct 15, 2013 9:22 am
- ECU Model: P8 Pro
- Distributor: second hand
- Firmware Version: 29
Re: Wiring to switch Map from Dash
"edited"
apologies for any inconvenience
apologies for any inconvenience
Last edited by mitsakos on Sun Nov 03, 2013 4:43 am, edited 1 time in total.
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Wiring to switch Map from Dash
No idea how that is relevant ?
E48 has only one map option does it not ?
Or what is the actual question ( and a new thread would be appropriate, as this one has nothing to do with a POT Box )
E48 has only one map option does it not ?
Or what is the actual question ( and a new thread would be appropriate, as this one has nothing to do with a POT Box )