My throttle body is pretty big 100mm.
Its running good at zero throttle and at 2%.
But it leans out in the middle of them
I use 0 2 4 % collums. How close can i set the collums ?
Any other trick to get around this problem ?
Big throttle body how much resolution can i use?
-
- Posts: 1250
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: Big throttle body how much resolution can i use?
1% is the min. but how about adding manifold pressure compensation as the corrections should be a straight line, and therefore just about automatic
Re: Big throttle body how much resolution can i use?
I dont have alot of vacum but il check in to it
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Big throttle body how much resolution can i use?
What is the engine, and why such a a large throttle ?
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: Big throttle body how much resolution can i use?
I'm always keen to see what it is when people say things like that...miler wrote:I dont have alot of vacum but il check in to it
Is it lean between no matter how slow you open it, or hold static? eg: it's not a throttle pump settings issue?
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
Re: Big throttle body how much resolution can i use?
Yes its lean in static and in slow movement.
Engine cbb 396 with big cam.
Plan is to build a 500+cui so i went big.
Engine cbb 396 with big cam.
Plan is to build a 500+cui so i went big.
- ignitionautosport
- Posts: 577
- Joined: Wed Jul 27, 2011 5:30 am
- ECU Model: S80 Pro
- Location: New Zealand
- Contact:
Re: Big throttle body how much resolution can i use?
I would change the columns, 0, 1, 2, 4, etc. Obviously you'll lose one up higher but I think thats a bearable trade-off.
If you have stuff all vacuum change overall it may not be worth adding MAP correction. Something to consider though.
If you have stuff all vacuum change overall it may not be worth adding MAP correction. Something to consider though.
| '94 GSR Lancer | '96 Toyota Carib 20V | '83 Toyota Starlet | www.ignitionautosport.co.nz |
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Big throttle body how much resolution can i use?
I'd think you could easily afford to use a few load sites down low for that, as after 50% or so the tuning changes needed would probably be much smaller and you could have them spaced much wider without it causing you any problems.
Re: Big throttle body how much resolution can i use?
Didnt clear that problem even with 1% but its getting better.
Just ordered me a new map sensor 1bar so i get better resulotion
But 80kpa at idle it will be Hard useing mappress anyway
Way better at low rpm compared to the old carburator
Now to a new question
While mapping (i dont have the knobs)
If i use the arrows to compensate fuel lets say im up 10%
How do i generate that change to the cell ?
And is there a way to reset the compensation?
Just ordered me a new map sensor 1bar so i get better resulotion
But 80kpa at idle it will be Hard useing mappress anyway
Way better at low rpm compared to the old carburator
Now to a new question
While mapping (i dont have the knobs)
If i use the arrows to compensate fuel lets say im up 10%
How do i generate that change to the cell ?
And is there a way to reset the compensation?
-
- Posts: 1250
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: Big throttle body how much resolution can i use?
Just return or F4 does the update, im sure its in the instructions!
But just make your self a knob box, you won't regret it.
What to you mean reset the compensation?
Just go to - Essential Map Settings/Manifold Pressure Compensations/Manifold/Baro pressure Compensations
Or do you mean the live adjustment compensation? if so you can't, if you have the knobs you can turn them on and off.
As you don't have the knobs box you are better off just changing the cell directly, then press F4 and it updates, it sounds like this is the problem not the tps resolution?
But just make your self a knob box, you won't regret it.
What to you mean reset the compensation?
Just go to - Essential Map Settings/Manifold Pressure Compensations/Manifold/Baro pressure Compensations
Or do you mean the live adjustment compensation? if so you can't, if you have the knobs you can turn them on and off.
As you don't have the knobs box you are better off just changing the cell directly, then press F4 and it updates, it sounds like this is the problem not the tps resolution?