Hi guys
Has anybody run a K20 engine successfully with a DTA S60 on stock sensors?
Honda K20 engine in Civic Type R
-
- Posts: 3588
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Honda K20 engine in Civic Type R
I think someone asked the same question a while back ? Isnt there a base map for one ?
Re: Honda K20 engine in Civic Type R
Yes, Loads of rally cars use them in Ireland
Re: Honda K20 engine in Civic Type R
Thanks - do you have any wiring info for them Antral?
And I presume they run fine on stock crank sensor etc?
And I presume they run fine on stock crank sensor etc?
Re: Honda K20 engine in Civic Type R
There is some info on the S60 wiring diag.
Stock sensors are fine.
Stock sensors are fine.
-
- Posts: 26
- Joined: Wed Jul 20, 2011 12:51 pm
- ECU Model: S80 Pro
- Distributor: www.mactecracing.com
- Firmware Version: 63
- Location: Thailand
Re: Honda K20 engine in Civic Type R
Confirm..!!! All Stock sensor are find !
Re: Honda K20 engine in Civic Type R
Do you have a wiring conversion diagram you could send?tecing wrote:Confirm..!!! All Stock sensor are find !
Re: Honda K20 engine in Civic Type R
Hi Guys,
OK - reading through the manual and could really do with some clarification on some points:
1) General Engine Settings, Mode 7 - sorted
2) Connect Inlet Cam Sensor to Pin 2. - Which is Inlet cam sensor? TDC Sensor (Pin A26 Honda Loom?)
3) Exhaust cam sensor to normal cam input, Pin 23. - Presume this is the one called "Cam" or pin A25 on the Honda Loom
4) Crank to Pin 13. - Self Explanatory
5) Road Speed in / out? Does the Honda Speedo work ok without Road speed in or out of ECU? Seems that Haltech doesn't use the Speed "out".
6) VTEC Control - Manual says connect to Aux 3, but which of the Honda wires? VTC+ (Pin B1), VTC- (Pin B23), VTEC Oil Pressure Switch (Pin B9) or VTEC Solenoid VTS+ (Pin B15)
7) TDC Sensor - A26 as above in point 2?
8) PGMFI Relay / IGN Signal - Needed - yes, use relay to control PGMFI with IGN.
Any input would be massively appreciated as what should have been a quick ECU job (like always!) seems to have become just the opposite!!
OK - reading through the manual and could really do with some clarification on some points:
1) General Engine Settings, Mode 7 - sorted
2) Connect Inlet Cam Sensor to Pin 2. - Which is Inlet cam sensor? TDC Sensor (Pin A26 Honda Loom?)
3) Exhaust cam sensor to normal cam input, Pin 23. - Presume this is the one called "Cam" or pin A25 on the Honda Loom
4) Crank to Pin 13. - Self Explanatory
5) Road Speed in / out? Does the Honda Speedo work ok without Road speed in or out of ECU? Seems that Haltech doesn't use the Speed "out".
6) VTEC Control - Manual says connect to Aux 3, but which of the Honda wires? VTC+ (Pin B1), VTC- (Pin B23), VTEC Oil Pressure Switch (Pin B9) or VTEC Solenoid VTS+ (Pin B15)
7) TDC Sensor - A26 as above in point 2?
8) PGMFI Relay / IGN Signal - Needed - yes, use relay to control PGMFI with IGN.
Any input would be massively appreciated as what should have been a quick ECU job (like always!) seems to have become just the opposite!!